Custom Pop
Forum rules
This section is for general Pop discussion, not showing off your recent acquisitions. Please use the Dance Hall for collection addition pictures.
Please post Funko subscription box and item discussions in the Powered By Funko section.
This section is for general Pop discussion, not showing off your recent acquisitions. Please use the Dance Hall for collection addition pictures.
Please post Funko subscription box and item discussions in the Powered By Funko section.
-
Jonny0boy
- Spirit Award

- Posts: 692
- Joined: Mon May 01, 2017 7:24 pm
- Location: Kent, Wa
- Contact:
Custom Pop
Thinking doing my first custon pop. Nees know what tols i need to do the head swap or something like that
i'm Jon and I am Hard of hearing
Been collecting since my first con at ECCC 2017
Funko Pops- 1,275

Been collecting since my first con at ECCC 2017
Funko Pops- 1,275

- YeetGrimes
- Spirit Award

- Posts: 3765
- Joined: Sun Jul 08, 2018 5:53 pm
- Location: San Diego, California
Re: Custom Pop
I'm going through the unanswered posts section since I hate seeing questions like these go unanswered, so sorry for the late reply.
To swap the head of the pop, start by putting it in some really hot water. That should loosen the glue enough so you can Pop! it right off

Not sure what would work to reattach the head, though. That's where I'm stuck
To swap the head of the pop, start by putting it in some really hot water. That should loosen the glue enough so you can Pop! it right off
Not sure what would work to reattach the head, though. That's where I'm stuck






- lavery01
- Collector of the Month

- Posts: 5988
- Joined: Sun Oct 23, 2016 7:13 pm
- Location: OC
Re: Custom Pop
Jonny0boy wrote:Thinking doing my first custon pop. Nees know what tols i need to do the head swap or something like that
Maybe not the best advice, but have you tried YouTube.
They are your one stop shop for how to’s.
Hi I'm Latricia 



- jjb11590
- Posts: 2554
- Joined: Wed Jan 02, 2019 11:29 am
- Location: Las Vegas
- Contact:
Re: Custom Pop
Jonny0boy wrote:Thinking doing my first custon pop. Nees know what tols i need to do the head swap or something like that
Sadly, I don't have any answers...but am curious if you had any luck yet (since your original post). I'd love to see what you've done so far.







IG/Twitter: jjb11590
- Hgmaddhatter
- Posts: 2158
- Joined: Tue Jul 24, 2018 3:37 pm
- Location: Florida
- Contact:
Re: Custom Pop
I use a pot of boiling water and gloves. Submerge your pops head up to the shoulders holding the feet until the vinyl is soft. Youll be able to tell its getting softer by squeezing the head.
Once you think its soft enough try pulling off the head, if you feel like your gonna break it then your vinyl is not soft enough. Be very careful at this point because water can seep into the head and thats how you get burnt.
After a few tries youll get it and it will be very easy in the future. As for reattaching that can be tricky. If you are doing a simple head swap then just boil your heads and reattach, easy peasy. If you are doing a repaint and have already applied paint, then you may not want to boil. If you cant just force it back on, which does sometimes work you can take an xacto knife and shave off some of the neck stump little by little untilyou can force it on, your head should be plenty sturdy as long as you dont cut off too much. If its wobbly you can glue it on but youll lose your head swivel.
Good luck! Hope this helps.
Once you think its soft enough try pulling off the head, if you feel like your gonna break it then your vinyl is not soft enough. Be very careful at this point because water can seep into the head and thats how you get burnt.
After a few tries youll get it and it will be very easy in the future. As for reattaching that can be tricky. If you are doing a simple head swap then just boil your heads and reattach, easy peasy. If you are doing a repaint and have already applied paint, then you may not want to boil. If you cant just force it back on, which does sometimes work you can take an xacto knife and shave off some of the neck stump little by little untilyou can force it on, your head should be plenty sturdy as long as you dont cut off too much. If its wobbly you can glue it on but youll lose your head swivel.
Good luck! Hope this helps.

- jjb11590
- Posts: 2554
- Joined: Wed Jan 02, 2019 11:29 am
- Location: Las Vegas
- Contact:
Re: Custom Pop
Hgmaddhatter wrote:I use a pot of boiling water and gloves. Submerge your pops head up to the shoulders holding the feet until the vinyl is soft. Youll be able to tell its getting softer by squeezing the head.
Once you think its soft enough try pulling off the head, if you feel like your gonna break it then your vinyl is not soft enough. Be very careful at this point because water can seep into the head and thats how you get burnt.
After a few tries youll get it and it will be very easy in the future. As for reattaching that can be tricky. If you are doing a simple head swap then just boil your heads and reattach, easy peasy. If you are doing a repaint and have already applied paint, then you may not want to boil. If you cant just force it back on, which does sometimes work you can take an xacto knife and shave off some of the neck stump little by little untilyou can force it on, your head should be plenty sturdy as long as you dont cut off too much. If its wobbly you can glue it on but youll lose your head swivel.
Good luck! Hope this helps.
This seems quite helpful! Do you have any pics of one's that you've done?







IG/Twitter: jjb11590
- Hgmaddhatter
- Posts: 2158
- Joined: Tue Jul 24, 2018 3:37 pm
- Location: Florida
- Contact:
Re: Custom Pop
jjb11590 wrote:Hgmaddhatter wrote:I use a pot of boiling water and gloves. Submerge your pops head up to the shoulders holding the feet until the vinyl is soft. Youll be able to tell its getting softer by squeezing the head.
Once you think its soft enough try pulling off the head, if you feel like your gonna break it then your vinyl is not soft enough. Be very careful at this point because water can seep into the head and thats how you get burnt.
After a few tries youll get it and it will be very easy in the future. As for reattaching that can be tricky. If you are doing a simple head swap then just boil your heads and reattach, easy peasy. If you are doing a repaint and have already applied paint, then you may not want to boil. If you cant just force it back on, which does sometimes work you can take an xacto knife and shave off some of the neck stump little by little untilyou can force it on, your head should be plenty sturdy as long as you dont cut off too much. If its wobbly you can glue it on but youll lose your head swivel.
Good luck! Hope this helps.
This seems quite helpful! Do you have any pics of one's that you've done?
Yeah, Although I haven't completed very many. I have a River Tam Custom with Box, a Flynn Rider from Tangled that I'm pretty happy with. My Fatso from Killer Klowns just needs a finished paint job, life happened and he's been half done for a few months now, right after I started him they released the NYCC Slim. All of them are made with basic supplies, acrylic paint, mod podge etc. I took a bunch of pictures of the process of making them and even tried video taping the Fatso. I've been toying with getting more serious about it and making some youtube videos as a hobby.




- jjb11590
- Posts: 2554
- Joined: Wed Jan 02, 2019 11:29 am
- Location: Las Vegas
- Contact:
Re: Custom Pop
Hgmaddhatter wrote:jjb11590 wrote:Hgmaddhatter wrote:I use a pot of boiling water and gloves. Submerge your pops head up to the shoulders holding the feet until the vinyl is soft. Youll be able to tell its getting softer by squeezing the head.
Once you think its soft enough try pulling off the head, if you feel like your gonna break it then your vinyl is not soft enough. Be very careful at this point because water can seep into the head and thats how you get burnt.
After a few tries youll get it and it will be very easy in the future. As for reattaching that can be tricky. If you are doing a simple head swap then just boil your heads and reattach, easy peasy. If you are doing a repaint and have already applied paint, then you may not want to boil. If you cant just force it back on, which does sometimes work you can take an xacto knife and shave off some of the neck stump little by little untilyou can force it on, your head should be plenty sturdy as long as you dont cut off too much. If its wobbly you can glue it on but youll lose your head swivel.
Good luck! Hope this helps.
This seems quite helpful! Do you have any pics of one's that you've done?
Yeah, Although I haven't completed very many. I have a River Tam Custom with Box, a Flynn Rider from Tangled that I'm pretty happy with. My Fatso from Killer Klowns just needs a finished paint job, life happened and he's been half done for a few months now, right after I started him they released the NYCC Slim. All of them are made with basic supplies, acrylic paint, mod podge etc. I took a bunch of pictures of the process of making them and even tried video taping the Fatso. I've been toying with getting more serious about it and making some youtube videos as a hobby.
Awesome job!







IG/Twitter: jjb11590
- Comicbookwriter
- Posts: 634
- Joined: Mon Jun 12, 2017 12:04 am
- Location: Downey
- Contact:
Who is online
Users browsing this forum: Baidu [Spider]

