Custom Pop

We're not talking about soda, folks. This forum is dedicated to Funko's stylish Pop! series of vinyl figures, with or without springs.
Forum rules
This section is for general Pop discussion, not showing off your recent acquisitions. Please use the Dance Hall for collection addition pictures.

Please post Funko subscription box and item discussions in the Powered By Funko section.
Jonny0boy
Spirit Award
Spirit Award
Posts: 692
Joined: Mon May 01, 2017 7:24 pm
Location: Kent, Wa
Contact:

Custom Pop

Postby Jonny0boy » Fri Oct 04, 2019 11:14 am

Thinking doing my first custon pop. Nees know what tols i need to do the head swap or something like that
i'm Jon and I am Hard of hearing
Been collecting since my first con at ECCC 2017
Funko Pops- 1,275


Image

User avatar
YeetGrimes
Spirit Award
Spirit Award
Posts: 3765
Joined: Sun Jul 08, 2018 5:53 pm
Location: San Diego, California

Re: Custom Pop

Postby YeetGrimes » Fri Dec 13, 2019 9:06 am

I'm going through the unanswered posts section since I hate seeing questions like these go unanswered, so sorry for the late reply.

To swap the head of the pop, start by putting it in some really hot water. That should loosen the glue enough so you can Pop! it right off :) lol

Not sure what would work to reattach the head, though. That's where I'm stuck lol
ImageImageImageImageImage ImageImage

User avatar
lavery01
Collector of the Month
Collector of the Month
Posts: 5988
Joined: Sun Oct 23, 2016 7:13 pm
Location: OC

Re: Custom Pop

Postby lavery01 » Mon Dec 23, 2019 1:33 pm

Jonny0boy wrote:Thinking doing my first custon pop. Nees know what tols i need to do the head swap or something like that


Maybe not the best advice, but have you tried YouTube. lol
They are your one stop shop for how to’s.
Hi I'm Latricia \:D/

Image

User avatar
jjb11590
Posts: 2554
Joined: Wed Jan 02, 2019 11:29 am
Location: Las Vegas
Contact:

Re: Custom Pop

Postby jjb11590 » Mon Dec 23, 2019 3:07 pm

Jonny0boy wrote:Thinking doing my first custon pop. Nees know what tols i need to do the head swap or something like that



Sadly, I don't have any answers...but am curious if you had any luck yet (since your original post). I'd love to see what you've done so far.
Image ImageImageImage

ImageImageImageImage

IG/Twitter: jjb11590

User avatar
Hgmaddhatter
Posts: 2158
Joined: Tue Jul 24, 2018 3:37 pm
Location: Florida
Contact:

Re: Custom Pop

Postby Hgmaddhatter » Mon Jan 20, 2020 2:18 pm

I use a pot of boiling water and gloves. Submerge your pops head up to the shoulders holding the feet until the vinyl is soft. Youll be able to tell its getting softer by squeezing the head.

Once you think its soft enough try pulling off the head, if you feel like your gonna break it then your vinyl is not soft enough. Be very careful at this point because water can seep into the head and thats how you get burnt.

After a few tries youll get it and it will be very easy in the future. As for reattaching that can be tricky. If you are doing a simple head swap then just boil your heads and reattach, easy peasy. If you are doing a repaint and have already applied paint, then you may not want to boil. If you cant just force it back on, which does sometimes work you can take an xacto knife and shave off some of the neck stump little by little untilyou can force it on, your head should be plenty sturdy as long as you dont cut off too much. If its wobbly you can glue it on but youll lose your head swivel.

Good luck! Hope this helps.
Image

User avatar
jjb11590
Posts: 2554
Joined: Wed Jan 02, 2019 11:29 am
Location: Las Vegas
Contact:

Re: Custom Pop

Postby jjb11590 » Wed Jan 22, 2020 6:54 pm

Hgmaddhatter wrote:I use a pot of boiling water and gloves. Submerge your pops head up to the shoulders holding the feet until the vinyl is soft. Youll be able to tell its getting softer by squeezing the head.

Once you think its soft enough try pulling off the head, if you feel like your gonna break it then your vinyl is not soft enough. Be very careful at this point because water can seep into the head and thats how you get burnt.

After a few tries youll get it and it will be very easy in the future. As for reattaching that can be tricky. If you are doing a simple head swap then just boil your heads and reattach, easy peasy. If you are doing a repaint and have already applied paint, then you may not want to boil. If you cant just force it back on, which does sometimes work you can take an xacto knife and shave off some of the neck stump little by little untilyou can force it on, your head should be plenty sturdy as long as you dont cut off too much. If its wobbly you can glue it on but youll lose your head swivel.

Good luck! Hope this helps.


This seems quite helpful! Do you have any pics of one's that you've done?
Image ImageImageImage

ImageImageImageImage

IG/Twitter: jjb11590

User avatar
Hgmaddhatter
Posts: 2158
Joined: Tue Jul 24, 2018 3:37 pm
Location: Florida
Contact:

Re: Custom Pop

Postby Hgmaddhatter » Fri Jan 24, 2020 4:32 pm

jjb11590 wrote:
Hgmaddhatter wrote:I use a pot of boiling water and gloves. Submerge your pops head up to the shoulders holding the feet until the vinyl is soft. Youll be able to tell its getting softer by squeezing the head.

Once you think its soft enough try pulling off the head, if you feel like your gonna break it then your vinyl is not soft enough. Be very careful at this point because water can seep into the head and thats how you get burnt.

After a few tries youll get it and it will be very easy in the future. As for reattaching that can be tricky. If you are doing a simple head swap then just boil your heads and reattach, easy peasy. If you are doing a repaint and have already applied paint, then you may not want to boil. If you cant just force it back on, which does sometimes work you can take an xacto knife and shave off some of the neck stump little by little untilyou can force it on, your head should be plenty sturdy as long as you dont cut off too much. If its wobbly you can glue it on but youll lose your head swivel.

Good luck! Hope this helps.


This seems quite helpful! Do you have any pics of one's that you've done?


Yeah, Although I haven't completed very many. I have a River Tam Custom with Box, a Flynn Rider from Tangled that I'm pretty happy with. My Fatso from Killer Klowns just needs a finished paint job, life happened and he's been half done for a few months now, right after I started him they released the NYCC Slim. All of them are made with basic supplies, acrylic paint, mod podge etc. I took a bunch of pictures of the process of making them and even tried video taping the Fatso. I've been toying with getting more serious about it and making some youtube videos as a hobby.

Image

Image

Image
Image

User avatar
jjb11590
Posts: 2554
Joined: Wed Jan 02, 2019 11:29 am
Location: Las Vegas
Contact:

Re: Custom Pop

Postby jjb11590 » Fri Jan 24, 2020 6:55 pm

Hgmaddhatter wrote:
jjb11590 wrote:
Hgmaddhatter wrote:I use a pot of boiling water and gloves. Submerge your pops head up to the shoulders holding the feet until the vinyl is soft. Youll be able to tell its getting softer by squeezing the head.

Once you think its soft enough try pulling off the head, if you feel like your gonna break it then your vinyl is not soft enough. Be very careful at this point because water can seep into the head and thats how you get burnt.

After a few tries youll get it and it will be very easy in the future. As for reattaching that can be tricky. If you are doing a simple head swap then just boil your heads and reattach, easy peasy. If you are doing a repaint and have already applied paint, then you may not want to boil. If you cant just force it back on, which does sometimes work you can take an xacto knife and shave off some of the neck stump little by little untilyou can force it on, your head should be plenty sturdy as long as you dont cut off too much. If its wobbly you can glue it on but youll lose your head swivel.

Good luck! Hope this helps.


This seems quite helpful! Do you have any pics of one's that you've done?


Yeah, Although I haven't completed very many. I have a River Tam Custom with Box, a Flynn Rider from Tangled that I'm pretty happy with. My Fatso from Killer Klowns just needs a finished paint job, life happened and he's been half done for a few months now, right after I started him they released the NYCC Slim. All of them are made with basic supplies, acrylic paint, mod podge etc. I took a bunch of pictures of the process of making them and even tried video taping the Fatso. I've been toying with getting more serious about it and making some youtube videos as a hobby.



Awesome job!
Image ImageImageImage

ImageImageImageImage

IG/Twitter: jjb11590

User avatar
Comicbookwriter
Posts: 634
Joined: Mon Jun 12, 2017 12:04 am
Location: Downey
Contact:

Re: Custom Pop

Postby Comicbookwriter » Thu Feb 13, 2020 2:20 am

Wow! This is great info for a head swap! Thanks!
Image


Return to “Pop!”

Who is online

Users browsing this forum: No registered users