New Frankenfreddy Project
-
phatjoe
New Frankenfreddy Project
I started a new Frankenfreddy today since I had a Herman head laying around from the last one I made. Next time will use A Freddy and Herman only instead of using handy dandy Franky head. Anyhow, I will be documenting the step by step process of doing this. If there is enough intrest I will post a "how to" so everyone can try. It's not very hard.
Joe
Joe
- creevox
- Posts: 728
- Joined: Sat Apr 26, 2003 3:56 pm
- Location: Glowsylvania
Awesome!!
Joe,
definitely post a how to along with the in progress photos!!!
I love watching and learning from talented artistic people!!!
I can do just about anything with photoshop, but can't draw a circle.
Joe,
definitely post a how to along with the in progress photos!!!
I love watching and learning from talented artistic people!!!
I can do just about anything with photoshop, but can't draw a circle.
A 38" all glow Glow Freddy would make me the happiest collector in history!!!!!
Ionraigh i Dorcha (That's Glow in the Dark in Gaelic)
蓄光
BBQ'n with a gas grill is not BBQ'n, it's cooking outside!!!!!
Ionraigh i Dorcha (That's Glow in the Dark in Gaelic)
蓄光
BBQ'n with a gas grill is not BBQ'n, it's cooking outside!!!!!
-
phatjoe
********DISCLAMER**********
Be careful with sharp objects. Be safe. Also there will be some very graphic wobbler pictures below so if you are squimish please look no further.
Supplies:
Make sure blade in knife is sharp....also soak heads(wobblers not your own) in warm water for 15min prior to doing any cutting. This softens up the plastic and makes it easier to cut..please be careful when using the knife..I have had many accidents and stiches in my model making years.
STEP 1
Remove Herman and Freddys faces.Make sure you make the cut on herman following the brow line:
STEP 2
I then lay the Hermans cut out face over Freddys and mark the top cut with a pen.
STEP 3
Test fit the face with the head...you will never get a perfect match..so trim a little at a time til you get somewhat of a flush fit up top and on the sides...the cheeks and bottom don't matter cause Freddy has big cheeks and they will overlap Hermans and the bottom gap will be filled later.
STEP 4
Next we glue the pieces together. Have tried many and the only one that seems to work is a 2 part epoxy made for plastics, PVC and soft plastics...the one pictured above is the best I have found so far. The epoxy is thick and helps to fill some gaps...but be carefull cause if you use to much it will run...what I do is use a little to tack the pieces in place and then after an hour I add more in the gaps. Do not worry about the big gaps.
We now have to wait 24 hours for the glue to cure (from previous experience if you don't once you add putty and start sanding the glued parts can come apart and you have to start over). Will post next installment soon, I go back to work tommorow.
Next we do the putty work and primer the figure.
Be careful with sharp objects. Be safe. Also there will be some very graphic wobbler pictures below so if you are squimish please look no further.
Supplies:
Make sure blade in knife is sharp....also soak heads(wobblers not your own) in warm water for 15min prior to doing any cutting. This softens up the plastic and makes it easier to cut..please be careful when using the knife..I have had many accidents and stiches in my model making years.
STEP 1
Remove Herman and Freddys faces.Make sure you make the cut on herman following the brow line:
STEP 2
I then lay the Hermans cut out face over Freddys and mark the top cut with a pen.
STEP 3
Test fit the face with the head...you will never get a perfect match..so trim a little at a time til you get somewhat of a flush fit up top and on the sides...the cheeks and bottom don't matter cause Freddy has big cheeks and they will overlap Hermans and the bottom gap will be filled later.
STEP 4
Next we glue the pieces together. Have tried many and the only one that seems to work is a 2 part epoxy made for plastics, PVC and soft plastics...the one pictured above is the best I have found so far. The epoxy is thick and helps to fill some gaps...but be carefull cause if you use to much it will run...what I do is use a little to tack the pieces in place and then after an hour I add more in the gaps. Do not worry about the big gaps.
We now have to wait 24 hours for the glue to cure (from previous experience if you don't once you add putty and start sanding the glued parts can come apart and you have to start over). Will post next installment soon, I go back to work tommorow.
Next we do the putty work and primer the figure.
- BobbleheadFreak
- Hall of Fame Class of 2020

- Posts: 2636
- Joined: Sun Nov 02, 2003 4:31 pm
- Location: Sacramento
- Contact:
- wizeguy
- Collector of the Month

- Posts: 1532
- Joined: Sat Apr 26, 2003 4:47 am
- NESSNODDER
- Hall of Fame Class of 2005

- Posts: 3100
- Joined: Sat Apr 26, 2003 4:02 am
- bobbleboy
- Hall of Fame Class of 2008

- Posts: 2495
- Joined: Sat Jul 12, 2003 8:38 pm
- Location: San Francisco, CA
- Contact:
-
uub
- mrcory5000
- Hall of Fame Class of 2006

- Posts: 3741
- Joined: Sun Apr 27, 2003 8:08 pm
- Location: House of 5000
- Contact:
- jarkbark
- Hall of Fame Class of 2008

- Posts: 1326
- Joined: Sat Apr 26, 2003 8:31 am
- Location: Chicago
- mrcory5000
- Hall of Fame Class of 2006

- Posts: 3741
- Joined: Sun Apr 27, 2003 8:08 pm
- Location: House of 5000
- Contact:
- pppmntpati
- Posts: 559
- Joined: Sun Apr 27, 2003 9:33 pm
- Location: New Hampshire
-
giantpez
Who is online
Users browsing this forum: No registered users




are you OK


